Limited availability - some workshops may not be available.
Guided Tour
Students will be led through the galleries to learn about telegraph, radio, radar, satellites and many more electronic marvels. There are plenty of hands on exhibits for students to explore too. This program costs $4 per student. Teachers and chaperones are free. Please allow 1 hour for this tour. Tours must be booked at least 2 weeks in advance.
Hands-On Demonstrations
A brief presentation featuring the museum's hands-on demonstrations followed by hands-on learning by the students. The demonstrations highlight subjects dealing with electricity and magnetism. This program costs $5 per student for just the hands-on demonstrations or $7 per student when combined with a guided tour. Teachers and chaperones are free. Please allow 1 hour for this program. Demos must be booked at least 2 weeks in advance. All of the Hands-On Demonstrations confirm with NGSS alignments. Contact nemuseum@gmail.com for details.
Workshops and Labs
The National Electronics Museum is setting up after moving. Hours are limited to by appointment. Not all of our workshops and labs are available currently. Contact the Museum for more details.
Booking and a nonrefundable payment for a workshop must be done at least 2 weeks before your group is scheduled to come.
Outreach Programs: If you can’t come to us, the Museum can bring our workshops and labs to you! There is a $0.55 per mile travel fee in addition to the cost of the Workshop. Outreach Programs must be scheduled three weeks in advance.
Minimum of 10 students required
Homo-Polar Motor Workshop: Build a direct current electric motor while learning about electricity and magnetism. Participants will construct the motor using copper or copper tinned wire, neodymium magnets and a standard AA battery. (45 minutes)
Workshop Cost $5.00/participant
- 4-PS3-2
- 3-5-ETS1-1
- 3-5-ETS1-2
- 3-5-ETS1-3
![](https://www.nationalelectronicsmuseum.org/media/images/HomoPolar-1.jpg)
![](https://www.nationalelectronicsmuseum.org/media/images/HomoPolar-2.jpg)
Simple Electromagnet Workshop: Learn about magnetism, electricity, basic circuits and power sources by building a simple electromagnet using insulated copper wire, a large screw and a battery pack. (45 minutes) Workshop Cost $5.00/participant
- 4-PS3-2
- 4-PS3-4
- 3-5-ETS1-1
- 3-5-ETS1-2
- 3-5-ETS1-3
- HS-PS2-5
- HS-PS3-5
![](https://www.nationalelectronicsmuseum.org/media/images/Simple-Electgromagnet-Workshop.jpg)
Nightlight Workshop: Using a breadboard, transistors, resistors and a light dependent resistor to construct your own nightlight! Soldering not required. (60 minutes)
Workshop Cost $10.00/participant
- 4-PS3-2
- 4-PS3-4
- 3-5-ETS1-1
- 3-5-ETS1-2
- 3-5-ETS1-3
![](https://www.nationalelectronicsmuseum.org/media/images/Night-Light-Workshop-scaled.jpg)
Light Bulb Interactive Demonstration: Have you ever wondered what type of light bulb is the most or least efficient in terms of energy usage? This workshop compares the incandescent bulb, the CFL bulb and the LED bulb with respect to current draw in Amperes and also how much heat is produced by each bulb type. (30 minutes)
Demonstration Cost $5.00/participant
Grade 4 and up Workshops:
Minimum of 10 students required
Simple Telegraph Workshop: Learn about series circuits and International Morse Code while constructing a simple code practice system. Participants will construct the Simple Telegraph using a clothespin as a Morse Code key, an electromechanical buzzer and a 9 Volt battery mounted on a foam base. (60 Minutes)
Workshop Cost $10.00/participant
- 4-PS3-2
- 4-PS3-4
- 4-PS4-3
- 3-5-ETS1-1
- 3-5-ETS1-2
- 3-5-ETS1-3
![](https://www.nationalelectronicsmuseum.org/media/images/Simple-Telegraph-Workshop-1-scaled.jpg)
Workshop Cost $15.00/participant
- 4-PS3-2
- 4-PS3-4
- 3-5-ETS1-1
- 3-5-ETS1-2
- 3-5-ETS1-3
- MS-PS1-4
![](https://www.nationalelectronicsmuseum.org/media/images/Electronic-Temperature-Sensor-Workshop-3-scaled.jpg)
Workshop Cost $12.00/participant
- 4-PS3-2
- 4-PS3-4
- 3-5-ETS1-1
- 3-5-ETS1-2
- 3-5-ETS1-3
![](https://www.nationalelectronicsmuseum.org/media/images/Basic-Flashlight-Workshop-scaled.jpg)
Minimum of 10 students required
Jumbo LED Flasher Workshop: Create your own jumbo LED flasher circuit using transistors, and other support components including a high quality printed circuit board. This workshop requires basic soldering skills. (90 minutes)
Workshop Cost $12.00/participant
- 3-5-ETS1-1
- 3-5-ETS1-2
- 3-5-ETS1-3
![](https://www.nationalelectronicsmuseum.org/media/images/Jumbo-LED-Flasher-Workshop-1.jpg)
![](https://www.nationalelectronicsmuseum.org/media/images/Jumbo-LED-Flasher-Workshop-scaled.jpg)
Minimum of 10 students required
555 Timer Workshop: Create a breadboard based LED blinker circuit using a 555 timer integrated circuit and other support components. Soldering not required. (90 minutes)
Workshop Cost $15.00/participant
- HS-PS3-3
![](https://www.nationalelectronicsmuseum.org/media/images/555-Timer-Workshop-scaled.jpg)
Minimum of 10 students required
Random Number Generator Workshop: Construct a random number generator circuit utilizing both analog and digital integrated circuits, a seven segment LED display and other support components. Soldering not required. (2 hours)
Workshop Cost $20.00/Participant
- HS-PS3-3
![](https://www.nationalelectronicsmuseum.org/media/images/RNG-JPEG060.jpg)
Theramin Workshop: Construct a Theramin circuit which is an electronic musical instrument using an analog integrated circuit, a light dependent resistor and other support components. Breadboard based. Soldering not required. (2 hours)
Workshop cost $18.00/participant
- HS-PS3-3
![](https://www.nationalelectronicsmuseum.org/media/images/Theramin-Workshop-scaled.jpg)
Workshop Cost $20.00/participant
- HS-PS3-3
![](https://www.nationalelectronicsmuseum.org/media/images/Electronic-Decision-Maker-Workshop.jpg)
Join this 5 hour weekend workshop to learn all about fiber optics technology and how it is deployed in our everyday lives. Then, build a fiber optic voice link kit to put what you have learned in class into practice. The voice link kit consists of a transmitter and receiver PC board with an interconnecting fiber optic link. A voice or tone signal is modulated by the transmitter and passed on to the fiber optic link. The receiver demodulates the signal from the fiber link and turns it back into a voice or tone based signal which is heard through the speaker. This workshop is geared for high school students and adults. Advanced soldering skills are required. The workshop is limited to 10 participants and is held on Saturdays throughout the year. Check our website for details. Workshop Cost $50.00/participant
- HS-PS4-2
![](https://www.nationalelectronicsmuseum.org/media/images/Fiber-Optics-Workshop-1.jpg)